Використовують пряму трубу з внутрішнім діаметром від 100 мм до 106 мм і довжиною 2,5 м. Поміщають один кінець цієї труби на середині профілю потоку основи камери або колодязя у вертикальному положенні, перпендикулярному до основи камери.
Скинути бойок типу d 90 (див. EN 744:1995) з масою 1 кг з висоти 2,5 м.
IMPACT TEST ON MANHOLE OR
CHAMBER BASES
D.1 Test equipment
The test equipment shall be as given in EN 744:1995.
D.2 Test procedure
Place the complete chamber base on a vee block in such a way that at least a 30 mm gap between base and block is achieved at point of impact.
For larger chamber bases, the apparatus can be modified to allow those chambers to fit - the vee block may be eliminated but the 30 mm gap shall remain between both the end of the guiding pipe and point of impact and between the ground and the base at the point of impact.
Use a straight pipe with an internal diameter of 100 mm to 106 mm and a length of 2,5 m. Place one end of this pipe in the middle of the main flow profile of the manhole or chamber base in a vertical position, perpendicular to the chamber base.
Drop a striker type d90 (see EN 744:1995) with mass 1 kg, from 2,5 m
.БІБЛІОГРАФІЯ
1 EN ISO 15493 Пластикові трубопровідні системи для промислового застосування. Акрило- нітрилбутадієнстирол (ABS), непластифікований полі (вінілхлорид) (PVC-U) і хлорований полі (вінілхлорид) (PVC-C). Технічні вимоги до компонентів і системи. Метрична серія (ISO 15493:2003)
2 EN ISO 15494 Пластикові трубопровідні системи для промислового застосування. Полібу- тилен (РВ), поліетилен (РЕ) і поліпропілен (РР). Технічні характеристики компонентів і системи. Метрична серія (ISO 15494:2003)
BIBLIOGRAPHY
1 EN ISO 15493, Plastic piping systems for industrial applications - Acrylonitrile-butadiene- styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specifications for components and the system - Metric series (ISO 15493:2003)
2 EN ISO 15494, Plastic piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the system - Metric series (ISO 15494:2003)
ПЕРЕЛІК ЧИННИХ НОРМАТИВНИХ ДОКУМЕНТІВ УКРАЇНИ,
ЩО ВІДПОВІДАЮТЬ МІЖНАРОДНИМ СТАНДАРТАМ,
НА ЯКІ Є ПОСИЛАННЯ В ЦЬОМУ СТАНДАРТІ
Познака та назва міжнародного стандарту |
Національний стандарт України, що відповідає міжнародному стандарту |
EN 12666-1, Plastics piping systems for non-pres- sure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
ДСТУ Б EN 12666-1:2011 Системи підземних безнапірних пластмасових трубопроводів для каналізації й дренажу. Поліетилен (РЕ). Частина 1. Технічні вимоги до труб, фітингів і системи (EN 12666-1:2005, IDT) |
EN 744:1995, Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method |
ДСТУ Б В.2.5-32:2007 Інженерне обладнання будинків і споруд. Зовнішні мережі та споруди. Труби безнапірні з поліпропілену, поліетилену, непластифікованого полівінілхлориду та фасонні вироби до них для зовнішніх мереж каналізації будинків і споруд та кабельної каналізації. Технічні умови |
EN 1401-1, Plastics piping systems for non-pres- sure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
|
EN 1852-1, Plastics piping systems for non-pres- sure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system |
|
EN 13476-1, Plastics piping systems for non-pres- sure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characteristics |
|
EN 13476-2, Plastics piping systems for non-pres- sure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A |
|
EN 13476-3, Plastics piping systems for non-pres- sure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type В |
Код УКНД 93.030
Ключові слова: зовнішні мережі, каналізація, дренаж, системи пластмасових трубопроводів, колодязі оглядові, камери ревізійні, вимоги, методи випробувань.
Редактор - А.О. Луковська
Комп’ютерна верстка - І.С. Дмитрук
Формат 60х841/в. Папір офсетний. Гарнітура "Arial".
Друк офсетний.
Державне підприємство "Укрархбудінформ".
вул. М. Кривоноса, 2А, м. Київ-37, 03037, Україна.
Тел. 249-36-62
Відділ реалізації: тел.факс (044) 249-36-62 (63, 64)
www.uabi.gov.ua E-mail:[email protected]
Свідоцтво про внесення суб’єкта видавничої справи до державного реєстру видавців
ДК № 690 від 27.11.2001 р.