---

The static and dynamic tests referred to in section 4.1.2.3 must be performed on all lifting machinery ready to be put into service.

Where the machinery cannot be assembled in the manufacturer's premises or in the premises of his authorised representative, the appropriate measures must be taken at the place of use. Otherwise, the measures may be taken either in the manufacturer's premises or at the place of use.

4.2. Requirements for machinery whose power source

is other than manual effort

4.2.1. Control of movements

Hold-to-run control devices must be used to control the movements of the machinery or its equipment. However, for partial or complete movements in which there is no risk of the load or the machinery colliding, the said devices may be replaced by control devices authorising automatic stops at pre-selected positions without the operator holding a hold-to-run control device.

4.2.2. Loading control

Machinery with a maximum working load of not less than or an overturning moment of not less than 40 000 Nm must be fitted with devices to warn the driver and prevent dangerous movements in the event:

- of overloading, either as a result of the maximum working load or the maximum working moment due to the load being exceeded,

or

- of the overturning moment being exceeded.

4.2.3. Installations guided by ropes

Rope carriers, tractors or tractor carriers must be held by counterweights or by a device allowing permanent control of the tension.

4.3. Information and markings

4.3.1. Chains, ropes and webbing

Each length of lifting chain, rope or webbing not forming part of an assembly must bear a mark or, where this is not possible, a plate or irremovable ring bearing the name and address of the manufacturer or his authorised representative and the identifying reference of the relevant certificate.

The certificate mentioned above must show at least the following information:

(a) the name and address of the manufacturer and, if appropriate, his authorised representative;

(b) a description of the chain or rope which includes:

- its nominal size,

- its construction,

- the material from which it is made, and

- any special metallurgical treatment applied to the material;

(c) the test method used;

(d) the maximum load to which the chain or rope should be subjected in service. A range of values may be given on the basis of the intended applications.

4.3.2. Lifting accessories

Lifting accessories must show the following particulars:

- identification of the material where this information is needed for safe use,

- the maximum working load.

In the case of lifting accessories on which marking is physically impossible, the particulars referred to in the first paragraph must be displayed on a plate or other equivalent means and securely affixed to the accessory.

The particulars must be legible and located in a place where they are not liable to disappear as a result of wear or jeopardise the strength of the accessory.

4.3.3. Lifting machinery

The maximum working load must be prominently marked on the machinery. This marking must be legible, indelible and in an un-coded form.

Where the maximum working load depends on the configuration of the machinery, each operating position must be provided with a load plate indicating, preferably in diagrammatic form or by means of tables, the working load permitted for each configuration.

Machinery intended for lifting goods only, equipped with a carrier which allows access to persons, must bear a clear and indelible warning prohibiting the lifting of persons. This warning must be visible at each place where access is possible.

4.4. Instructions

4.4.1. Lifting accessories

Each lifting accessory or each commercially indivisible batch of lifting accessories must be accompanied by instructions setting out at least the following particulars:

(a) the intended use;

(b) the limits of use (particularly for lifting accessories such as magnetic or vacuum pads which do not fully comply with section 4.1.2.6(e));

(c) instructions for assembly, use and maintenance;

(d) the static test coefficient used.

4.4.2. Lifting machinery

Lifting machinery must be accompanied by instructions containing information on:

(a) the technical characteristics of the machinery, and in particular:

- the maximum working load and, where appropriate, a copy of the load plate or load table described in the second paragraph of section 4.3.3,

- the reactions at the supports or anchors and, where appropriate, characteristics of the tracks,

- where appropriate, the definition and the means of installation of the ballast;

(b) the contents of the logbook, if the latter is not supplied with the machinery;

(c) advice for use, particularly to offset the lack of direct vision of the load by the operator;

(d) where appropriate, a test report detailing the static and dynamic tests carried out by or for the manufacturer or his authorised representative;

(e) for machinery which is not assembled on the premises of the manufacturer in the form in which it is to be used, the necessary instructions for performing the measures referred to in section 4.1.3 before it is first put into service.

5. SUPPLEMENTARY ESSENTIAL HEALTH AND SAFETY

REQUIREMENTS FOR MACHINERY INTENDED FOR UNDERGROUND WORK

Machinery intended for underground work must meet all the essential health and safety requirements described in this chapter (see General Principles, point 4).

5.1. Risks due to lack of stability

Powered roof supports must be designed and constructed in such a way as to maintain a given direction when moving and not slip before and while they come under load and after the load has been removed. They must be equipped with anchorages for the top plates of the individual hydraulic props.

5.2. Movement

Powered roof supports must allow for unhindered movement of persons.

5.3. Control devices

The accelerator and brake controls for movement of machinery running on rails must be hand-operated. However, enabling devices may be foot-operated.

The control devices of powered roof supports must be designed and positioned in such a way that, during displacement operations, operators are sheltered by a support in place. The control devices must be protected against any accidental release.

5.4. Stopping

Self-propelled machinery running on rails for use in underground work must be equipped with an enabling device acting on the circuit controlling the movement of the machinery such that movement is stopped if the driver is no longer in control of the movement.

5.5. Fire

The second indent of section 3.5.2 is mandatory in respect of machinery which comprises highly flammable parts.

The braking system of machinery intended for use in underground workings must be designed and constructed in such a way that it does not produce sparks or cause fires.

Machinery with internal combustion engines for use in underground workings must be fitted only with engines using fuel with a low vaporising pressure and which exclude any spark of electrical origin.

5.6. Exhaust emissions

Exhaust emissions from internal combustion engines must not be discharged upwards.

6. SUPPLEMENTARY ESSENTIAL HEALTH AND SAFETY

REQUIREMENTS FOR MACHINERY PRESENTING PARTICULAR HAZARDS DUE

TO THE LIFTING OF PERSONS

Machinery presenting hazards due to the lifting of persons must meet all the relevant essential health and safety requirements described in this chapter (see General Principles, point 4).

6.1. General

6.1.1. Mechanical strength

The carrier, including any trapdoors, must be designed and constructed in such a way as to offer the space and strength corresponding to the maximum number of persons permitted on the carrier and the maximum working load.

The working coefficients for components set out in sections 4.1.2.4 and 4.1.2.5 are inadequate for machinery intended for the lifting of persons and must, as a general rule, be doubled. Machinery intended for lifting persons or persons and goods must be fitted with a suspension or supporting system for the carrier designed and constructed in such a way as to ensure an adequate overall level of safety and to prevent the risk of the carrier falling.

If ropes or chains are used to suspend the carrier, as a general rule, at least two independent ropes or chains are required, each with its own anchorage.

6.1.2. Loading control for machinery moved by power other than human strength

The requirements of section 4.2.2 apply regardless of the maximum working load and overturning moment, unless the manufacturer can demonstrate that there is no risk of overloading or overturning.

6.2. Control devices

Where safety requirements do not impose other solutions, the carrier must, as a general rule, be designed and constructed in such a way that persons in the carrier have means of controlling upward and downward movements and, if appropriate, other movements of the carrier.

In operation, those control devices must override any other devices controlling the same movement with the exception of emergency stop devices.

The control devices for these movements must be of the hold-to-run type except where the carrier itself is completely enclosed.

6.3. Risks to persons in or on the carrier

6.3.1. Risks due to movements of the carrier

Machinery for lifting persons must be designed, constructed or equipped in such a way that the acceleration or deceleration of the carrier does not engender risks for persons.

6.3.2. Risk of persons falling from the carrier

The carrier must not tilt to an extent which creates a risk of the occupants falling, including when the machinery and carrier are moving.

Where the carrier is designed as a work station, provision must be made to ensure stability and to prevent hazardous movements.

If the measures referred to in section 1.5.15 are not adequate, carriers must be fitted with a sufficient number of suitable anchorage points for the number of persons permitted on the carrier. The anchorage points must be strong enough for the use of personal protective equipment against falls from a height.

Any trapdoor in floors or ceilings or side doors must be designed and constructed in such a way as to prevent inadvertent opening and must open in a direction that obviates any risk of falling, should they open unexpectedly.

6.3.3. Risk due to objects falling on the carrier

Where there is a risk of objects falling on the carrier and endangering persons, the carrier must be equipped with a protective roof.

6.4. Machinery serving fixed landings

6.4.1. Risks to persons in or on the carrier

The carrier must be designed and constructed in such a way as to prevent risks due to contact between persons and/or objects in or on the carrier with any fixed or moving elements. Where necessary in order to fulfil this requirement, the carrier itself must be completely enclosed with doors fitted with an interlocking device that prevents hazardous movements of the carrier unless the doors are closed. The doors must remain closed if the carrier stops between landings where there is a risk of falling from the carrier.

The machinery must be designed, constructed and, where necessary, equipped with devices in such a way as to prevent uncontrolled upward or downward movement of the carrier. These devices must be able to stop the carrier at its maximum working load and at the foreseeable maximum speed.

The stopping action must not cause deceleration harmful to the occupants, whatever the load conditions.

6.4.2. Controls at landings

Controls, other than those for emergency use, at landings must not initiate movements of the carrier when:

- the control devices in the carrier are being operated,

- the carrier is not at a landing.

6.4.3. Access to the carrier

The guards at the landings and on the carrier must be designed and constructed in such a way as to ensure safe transfer to and from the carrier, taking into consideration the foreseeable range of goods and persons to be lifted.

6.5. Markings

The carrier must bear the information necessary to ensure safety including:

- the number of persons permitted on the carrier,

- the maximum working load.

Annex II

DECLARATIONS

1. CONTENT

A. EC declaration of conformity of the machinery

This declaration and translations thereof must be drawn up under the same conditions as the instructions (see Annex I, section 1.7.4.1(a) and (b)), and must be typewritten or else handwritten in capital letters.

This declaration relates exclusively to the machinery in the state in which it was placed on the market, and excludes components which are added and/or operations carried out subsequently by the final user.

The EC declaration of conformity must contain the following particulars:

1. business name and full address of the manufacturer and, where appropriate, his authorised representative;

2. name and address of the person authorised to compile the technical file, who must be established in the Community;

3. description and identification of the machinery, including generic denomination, function, model, type, serial number and commercial name;

sentence expressly declaring that the machinery fulfils all the relevant provisions of this Directive and where appropriate, a similar sentence declaring the conformity with other Directives and/or relevant provisions with which the machinery complies. These references must be those of the texts published in the Official Journal of the European Union;

5. where appropriate, the name, address and identification number of the notified body which carried out the EC type-examination referred to in Annex IX and the number of the EC type-examination certificate;

6. where appropriate, the name, address and identification number of the notified body which approved the full quality assurance system referred to in Annex X;

7. where appropriate, a reference to the harmonised standards used, as referred to in Article 7(2);

8. where appropriate, the reference to other technical standards and specifications used;

9. the place and date of the declaration;

10. the identity and signature of the person empowered to draw up the declaration on behalf of the manufacturer or his authorised representative.

B. Declaration of incorporation of partly

completed machinery

This declaration and translations thereof must be drawn up under the same conditions as the instructions (see Annex 1, section 1.7.4.1(a) and (b)), and must be typewritten or else handwritten in capital letters.

The declaration of incorporation must contain the following particulars:

1. business name and full address of the manufacturer of the partly completed machinery and, where appropriate, his authorised representative;

2. name and address of the person authorised to compile the relevant technical documentation, who must be established in the Community;

3. description and identification of the partly completed machinery including generic denomination, function, model, type, serial number and commercial name;

sentence declaring which essential requirements of this Directive are applied and fulfilled and that the relevant technical documentation is compiled in accordance with part B of Annex VII, and, where appropriate, a sentence declaring the conformity of the partly completed machinery with other relevant Directives. These references must be those of the texts published in the Official Journal of the European Union;

5. an undertaking to transmit, in response to a reasoned request by the national authorities, relevant information on the partly completed machinery. This shall include the method of transmission and shall be without prejudice to the intellectual property rights of the manufacturer of the partly completed machinery;

statement that the partly completed machinery must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the provisions of this Directive, where appropriate;

7. the place and date of the declaration;

8. the identity and signature of the person empowered to draw up the declaration on behalf of the manufacturer or his authorised representative.

2. CUSTODY

The manufacturer of machinery or his authorised representative shall keep the original EC declaration of conformity for a period of at least 10 years from the last date of manufacture of the machinery.

The manufacturer of partly completed machinery or his authorised representative shall keep the original declaration of incorporation for a period of at least 10 years from the last date of manufacture of the partly completed machinery.

Annex III

CE MARKING

The CE conformity marking shall consist of the initials "CE" taking the following form <*>:

--------------------------------

<*> Рис. не приводится.

If the CE marking is reduced or enlarged the proportions shown in the above drawing must be respected.

The various components of the CE marking must have substantially the same vertical dimension, which may not be less than . The minimum dimension may be waived for small-scale machinery.

The CE marking must be affixed in the immediate vicinity of the name of the manufacturer or his authorised representative, using the same technique.

Where the full quality assurance procedure referred to in Article 12(3)(c) and 12(4)(b) has been applied, the CE marking must be followed by the identification number of the notified body.

Annex IV

CATEGORIES OF MACHINERY TO WHICH ONE OF THE PROCEDURES

REFERRED TO IN ARTICLE 12(3) AND (4) MUST BE APPLIED

1. Circular saws (single- or multi-blade) for working with wood and material with similar physical characteristics or for working with meat and material with similar physical characteristics, of the following types:

1.1. sawing machinery with fixed blade(s) during cutting, having a fixed bed or support with manual feed of the workpiece or with a demountable power feed;

1.2. sawing machinery with fixed blade(s) during cutting, having a manually operated reciprocating saw-bench or carriage;

1.3 sawing machinery with fixed blade(s) during cutting, having a built-in mechanical feed device for the workpieces, with manual loading and/or unloading;

1.4. sawing machinery with movable blade(s) during cutting, having mechanical movement of the blade, with manual loading and/or unloading.

2. Hand-fed surface planing machinery for woodworking.

3. Thicknessers for one-side dressing having a built-in mechanical feed device, with manual loading and/or unloading for woodworking.

4. Band-saws with manual loading and/or unloading for working with wood and material with similar physical characteristics or for working with meat and material with similar physical characteristics, of the following types:

4.1. sawing machinery with fixed blade(s) during cutting, having a fixed or reciprocating-movement bed or support for the workpiece;

4.2. sawing machinery with blade(s) assembled on a carriage with reciprocating motion.

5. Combined machinery of the types referred to in points 1 to 4 and in point 7 for working with wood and material with similar physical characteristics.

6. Hand-fed tenoning machinery with several tool holders for woodworking.

7. Hand-fed vertical spindle moulding machinery for working with wood and material with similar physical characteristics.

8. Portable chainsaws for woodworking.

9. Presses, including press-brakes, for the cold working of metals, with manual loading and/or unloading, whose movable working parts may have a travel exceeding and a speed exceeding 30 mm/s.

10. Injection or compression plastics-moulding machinery with manual loading or unloading.

11. Injection or compression rubber-moulding machinery with manual loading or unloading.

12. Machinery for underground working of the following types:

12.1. locomotives and brake-vans;

12.2. hydraulic-powered roof supports.

13. Manually loaded trucks for the collection of household refuse incorporating a compression mechanism.

14. Removable mechanical transmission devices including their guards.

15. Guards for removable mechanical transmission devices.

16. Vehicle servicing lifts.

17. Devices for the lifting of persons or of persons and goods involving a hazard of falling from a vertical height of more than three metres.

18. Portable cartridge-operated fixing and other impact machinery.

19. Protective devices designed to detect the presence of persons.

20. Power-operated interlocking movable guards designed to be used as safeguards in machinery referred to in points 9, 10 and 11.

21. Logic units to ensure safety functions.

22. Roll-over protective structures (ROPS).

23. Falling-object protective structures (FOPS).

Annex V

INDICATIVE LIST

OF THE SAFETY COMPONENTS REFERRED TO IN ARTICLE 2(C)

1. Guards for removable mechanical transmission devices.

2. Protective devices designed to detect the presence of persons.

3. Power-operated interlocking movable guards designed to be used as safeguards in machinery referred to in items 9, 10 and 11 of Annex IV.

4. Logic units to ensure safety functions.

5. Valves with additional means for failure detection intended for the control of dangerous movements on machinery.

6. Extraction systems for machinery emissions.

7. Guards and protective devices designed to protect persons against moving parts involved in the process on the machinery.

8. Monitoring devices for loading and movement control in lifting machinery.

9. Restraint systems to keep persons on their seats.

10. Emergency stop devices.

11. Discharging systems to prevent the build-up of potentially dangerous electrostatic charges.

12. Energy limiters and relief devices referred to in sections 1.5.7, 3.4.7 and 4.1.2.6 of Annex I.

13. Systems and devices to reduce the emission of noise and vibrations.

14. Roll-over protective structures (ROPS).

15. Falling-object protective structures (FOPS).

16. Two-hand control devices.

17. Components for machinery designed for lifting and/or lowering persons between different landings and included in the following list:

(a) devices for locking landing doors;

(b) devices to prevent the load-carrying unit from falling or unchecked upwards movement;

(c) overspeed limitation devices;

(d) energy-accumulating shock absorbers,